11/21/2023 0 Comments Restrained spring isolatorsWebsite Custom Crafted by Bright Cloud Studio. Vibration isolators shall be Model FLS as manufactured by Kinetics Noise Control, Inc. Springs shall be color coded or otherwise identified to indicate load capacity. Springs shall be selected to provide static deflections shown on the Vibration Isolation Schedule or as indicated on the project documents. Non-welded spring elements shall be polyester powder coated, and shall have a 1000 hr rating when tested in accordance with ASTM B-117. Spring elements shall have a lateral stiffness greater than 1.2 times the rated vertical stiffness and shall be designed to provide a minimum of 50% overload capacity. Housing should be designed to provide a constant free and operating height within 1/8" (0.06 mm). Housing shall be electrozinc plated or hot dip galvanized for corrosion resistance. Housing assemblies shall be fabricated steel members and shall consist of a top load plate complete with adjusting and leveling bolts, vertical restraints, isolation washers and a bottom plate with internal non-skid noise isolation pads. Vibration isolators for equipment which is subject to load variations and large external or torquing forces shall consist of large diameter laterally stabile steel springs assembled into welded steel housing assemblies designed to limit vertical movement of the supported equipment. Kinetics Model FLS spring isolators are recommended for the isolation of vibration producing equipment carrying a large fluid load which may be drained, such as boilers, cooling towers and chillers, and for the isolation of outdoor components such as cooling towers, air-cooled condensers, etc., where wind loads are minimal. Restrained rubber vibration isolators is placed between the mechanical equipment and the floor and is used to absorb high frequency vibrations in this equipment. Custom isolators with higher deflection and greater load capabilities are available. Types of Linkran restrained rubber vibration isolators include rubber with specified hardness and cast iron frame. FLS Springs are available with deflections to 4" (102 mm) and with load capacities to 23,200 lbs. To assure stability, the springs have lateral spring stiffness greater than 1.2 times the rated vertical stiffness, and are designed to provide a minimum of 50% overload capacity. The isolator can be welded to the structure as well. Holes are provided in all isolators for bolting to the structure and to the supported equipment. Springs are polyester powder coated, with a 1000-hour salt spray rating per ASTM B-117. As with any seismic restraint or vibration isolation. and provide up to 4-inches of deflection. The modular design of the TITAN allows it to handle loads up to 23,200 lbs. A clearance of 1/4 (6mm) shall be maintained around restraining bolts and the. Spring elements are complete with internal noise isolation pads and have an adjusting and leveling bolt as a part of the top load plate assembly. The TITAN isolator/restraint is recommended for equipment mounted on a structural frame or concrete inertia base where the top plate of the isolator can be fully utilized. Restraining Bolts shall have a neoprene bushing between the bolt and the housing. The housings also provide a constant free and operating height to facilitate installation. Kinetics Model FLS vibration isolators consist of free-standing, large diameter, laterally stable steel springs assembled into welded steel housing assemblies fabricated to limit vertical movement of the isolated equipment if equipment loads are reduced, or if the equipment is subjected to large vertical external forces. KSR 2.KINETICS® FLS-1 & FLS-2 Restrained Spring Isolators HSR Thrust Restraint Roof Isolation Curbs and Rails Model Name Housekeeping Pad Mounted Using KCAB Anchors and KSUA Clips TITAN Modular Seismic and Wind Restraint Vibration Isolator Inline pump isolated concrete inertia baseįHS Seismic Restrained Spring Isolator with Optional Oversized BaseplateįLS Restrained Spring Isolator with Optional Oversized BaseplateįLSS Seismic Restrained Spring Isolator with Optional Oversized Baseplate Isolation curb acoustical treatment option 2 Isolation curb acoustical treatment option 1 Isolated equipment attached to equipment supportĮnd Suction pump isolated concrete inertia base The details are sorted in alphabetical order by product model name. The details can be easily imported into your specification documents or plans. Kinetics Middle East is proud to offer details of our products in AutoCAD, Revit (BIM) and PDF format. Product Details in BIM (REVIT), AutoCAD (DWG) and PDF Downloads
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |